7 X 14 Mini Metal Lathe 1.2 HP Servo Motor 115 V 900 Watt Kit upgrade conversion

  

2023 Upgraded 1.2 HP 900 Watt Computer Controller With internal rotary speed control switch and Matching Servo Motor. See image 1 for whats in the box. All other images are for information only. Only for Spindle Drive 7 X 14 Mini Lathe.

Does not fit 8 X 14 lathes. Does not fit 2 speed mini lathes.

Make note: These are 900 watt systems, not 750 watt systems. The difference is more low end HP and less high speed RPM's. Fits Many Mini Metal Lathes. In the original motor location of your spindle drive mini metal lathe. Of all threading gears and auto feed systems. Each one is custom built when you order. When the build is complete, it will be tested for 20 minuets. Any defects found during testing will require a complete new build. All parts required to build are In stock items. T In stock: Built with the new designs for 2023. Fits mini metal lathes that the drive belt goes directly to the spindle gear. Does not fit mini metal lathes that have an intermediate shaft (high/low gear). 185240421319 or 900W - 2 speed.

Ndividual parts, timing belt with timing gears, spacers and adapters are available. Separately so if you plan to use a Vevor, you will have to weld your own. Instead, see my other listings for a complete kit. Kinda like replacing the small block with a big block in your Mustang/Camaro muscle car. Just pure power, so much so that you will never use all of it.

This system provides full power at any speed and that includes Spindle RPM's as low as 200 RPM's. Motor and spindle speeds + Reverse. The motor speed can be.

And or full range can be achieved with just the speed control lever. Only requires a few easy steps. Reverse is simple, just hold the yellow button for a few seconds. Includes the ability to set bottom and top RPM range separately. In other words you can program the system to run the spindle at any speed or range of speeds you choose (see below).

Slowest speed achievable: Motor 100 RPM = Spindle 60 RPM. Highest speed this one produced: Motor 3,500 RPM = Spindle just over 2,000 RPM's.

Note: it is not recommended to spin the spindle any faster unless you upgrade the factory installed spindle bearings. RPM: 100 to 3,500 RPM in 100 RPM increments. See it (prototype 1) running. On You Tube search for. Mini Metal Lathe 1 HP Servo Motor 750 Watt Computer controlled with threading and gears Same username The Custom Crafter. System includes: Control unit comes fully programed for your system. A new 900 watt motor like the one seen here in photos above and on you-tube.

Motor will come with the motor mount installed. This will require adjustment to fit your lathe.

It will also come with the small timing pulley installed on it using a 5 mm key-way and main shaft nut. A new 2023 control computer like the one seen in the above photos. This control unit is built by The Custom Crafter to include: A.

Built in Thermal overload protection rocker style switch with reset function. See photos, make note of the orange power switch with the word RESET. If your switch is red or if it does not say reset, it does not have thermal overload protection. Internal speed control rotary switch.

The Custom Crafter made in the USA motor mount. (installed on motor, see line 1). Includes thick washers and grade 8 nuts. The Custom Crafter made in USA spindle bearing head adapter (see photos). The Custom Crafter made in USA spindle spacer (see photos).

One custom made polished and anodized aluminum spindle timing pulley (see photos). One custom made polished and anodized aluminum motor timing pulley (see photos).

Comes preinstalled on motor (see line 1). A new L050 1/2 wide timing belt. Access to on line active programming instructions and fault codes in plain English and written by us..

Includes recommended programming settings and fault codes. The Custom Crafter quick program and spindle speed card. Package will include basic written assembly instructions.

This will include a text number for direct assistance from the custom Crafter. Assembly requires some technical skill to include minor machine work. Note: Check the photos in this listing. If your lathe has holes instead of the normal slots, this motor will not fit without your ability to slot the cast iron lathe bed.

You will have to cut the die-cast gear housing to allow additional room for the larger timing belt. (see photos) this can be done with a hacksaw and a file but a pneumatic cut off tool or die grinder will ease this job.

A spreader wrench is a big help but this can be managed with a hammer and punch. You will need metric and domestic allen wrenches + a 13mm/1/2 deep socket and ratchet. Some longer allen head metric allen head bolts (not included) may also be required, especially it you over tighten and strip the factory bolts provided with your machine. This system has so much more power that it becomes tempting to see just how much you can cut in a single pass.

Do not do this because the rest of the mini lathe is not built strong/stable enough for this kind of abuse. If you jam it, you may damage the lathe to include broken cutters, parts and the control unit. All lathes are dangerous, increasing the. To insure fit and proper application. Is suitable for your intended use. I love it great product and support. Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit Fits Original Location Gear. Awesome product, crazy power output, thanks! Took me about an hour to install I still have to make a mount for the controller. What a amazing enhancement to my lathe.

Thank you very much for your time invested with developing a product for a very fair price that is an amazing enhancement. Large flat rate box and to USA only.

Be added to the order. Main components have a unique internal water soluble identification mark. No return authorizations will be issued after the 10 day period. See details, what's covered and for how long etc below.

If found to be abuse or missing the. Or demos that I have from previous builds.

Additionally original packaging such as Styrofoam package inserts must be used to return these parts. Timing pulleys, motor mount and aluminum adapters. Timing belt and small parts are not covered. Please contact me because as long as there is no abuse, I will offer a solution. This often includes parts at cost and free installation. I will also provide the same service to repair your system for up to a year.

Just return it with an honest answer as to why it failed, to include things like I jammed it and smoked it. I will fix it for you at my cost for parts. Yes, I keep control boards in stock for this reason.

I also keep motors, belts and every part used to build these in stock. Just contact me and we will have you up and running within days, not 6 months waiting for parts from China. Ask questions before ordering: Do not worry about missing this item. Also as I build them, they are improved as I never cut corners to save penny's.