1998-2004 2nd Gen S10 Manual Brake Conversion Kit 1.0 Bore Master Cylinder

  
THE SUPERIOR MANUAL BRAKE CONVERSION KIT. Doesn't Your S-10 Deserve the Best? NOTE: This kit will require drilling a 9/16" hole in the firewall and a 35/64" hole in the brake pedal to be installed correctly. If needed, please contact me with any additional questions about the installation. Kit with NO Master Cylinder and NO Brake Line Adapters.

Use almost any master cylinder (GM, Ford, MOPAR, Strange, Wilwood, Baer). 7/8 Bore Master Cylinder Applications.

Front Stock Disc Brake (D154 Calipers). Rear Stock or Aftermarket Drum. Front S-10 Blazer Twin Piston Disc Brake Conversion. Front Wilwood Disc Brake Kit Conversion Kit.

15/16 Bore Master Cylinder Applications. Front Stock Disc Brake (D154 Caliper).

Rear Stock GM, Factory Calipers (NON-Metric) Disc Brake Conversion Kit. Rear Wilwood Disc Brake Conversion Kit - 1.38 4 piston diameter or smaller. 1.0 Bore Manual Brake Applications. Front Stock Front Disc (D154 Metric Caliper).

Rear GM Metric (D154) Caliper Disc Brake Conversion Kit. Rear Wilwood Disc Brake Conversion Kit - 1.75 4 piston diameter or larger. Stock GM, Front Metric (D154) Caliper on rear. Front B-Body Disc Brake Conversion Kit (D52 Caliper).

1.03 Bore Manual Brake Applications. Rear TBM/Strange/Aerospace Disc Brake Conversion Kit.

1.125 Bore Master Cylinder Applications. Rear all disc brake conversion kit setups.

This manual brake conversion kit comes with. · 6061-T6 ALUMINUM adapter plate w/ integrated pushrod retention cup. · Matching Rubber Firewall Gasket - Keeps the engine bay sealed from the cars interior. · Stainless Steel Mounting Hardware - NO rusty bolts or nuts.

Adjustable Pushrod Assembly - Engineered to work with and function correctly with your vehicle. · Master cylinder with the bore size listed in the ad.

· Brake Line Adapters - For ease of installing stock brake lines to the master cylinder supplied in the kit. · Detailed (5 Page) Installation Manual. · 6 to 1 Pedal Ratio - Creates less effort by the driver to stop the car and multiplies the fluid pressure in the system. No other manual brake conversion kit can match this. · Dual Bolt Patter on the Adapter Plate - Use GM, Ford, or MOPAR master cylinders. No other manual brake conversion kit can do this. · Better pedal modulation for consistent braking - No low engine vacuum issues to worry about. The adapter plate is CNC machined by a water jet from rigid 1/8 thick aluminum with dimensions that covers up the hole in the firewall after you remove the power booster. This modification will clean up your firewall by getting rid of the big, bulky power booster. Racers do this swap when their engine does not make enough vacuum to operate the power booster, to shed a few pounds to make their car lighter, or to clean up the engine bay. The pro-touring fans use manual brakes to get a better "feel" of their brakes when heading into a corner at a high rate of speed. The adapter plate can also be polished up to a mirror finish if needed. · Higher Pedal Ratio = Less Leg Effort = Increased Braking Performance. · Smaller Bore Master Cylinder = Higher Fluid Pressure = Increased Braking Performance. · Kit comes with a gasket matched to the adapter plate to seal the passenger compartment from the engine bay. The other kits do not offer a gasket in their kits. · Kit comes with a dual bolt pattern to run different master cylinders from GM, Ford, and MOPAR. The other manual brakes kits do not have this feature. · Kit comes with the correct size master cylinder that is matched to the size of the front and rear brakes. The other manual brake kits offer a larger bore master cylinder which generates less brake line pressure.

· NON Low Drag Caliper (see below) - These type of calipers are mandatory to work with the supplied master cylinder. · New Rubber or Stainless Steel Flexible Brakes Lines (front and rear) - Old rubber lines will "balloon" causing loss of pressure within the braking system. · LOW drag calipers came on ALL first generation S10 trucks and SUVs. · All replacement calipers, with stock piston size, should be rebuilt to NON low drag standards and will work with this KIT.

I will be happy to answer any of your questions.