1982-1994 1st Gen S10 Manual Brake Conversion Kit Disc / Drum 7/8 Bore MC

THE SUPERIOR MANUAL BRAKE CONVERSION KIT. Doesn't Your S-10 Deserve the Best? For Disc / Disc KIT with stock rear calipers or four piston calipers with 1.38, or smaller, pistons. For Disc / Disc KIT with Metric calipers or four piston calipers with 1.75, or larger, pistons. If you have Strange or Aerospace front or rear calipers, contact Strange or Aerospace for correct size master cylinder.

This S10 manual brake conversion kits comes with. 6061-T6 ALUMINUM adapter plate w/ integrated pushrod retention cup.

Matching Rubber Firewall Gasket - Keeps the engine bay sealed from the cars interior. Stainless Steel Mounting Hardware - NO rusty bolts or nuts. Adjustable Pushrod Assembly - Engineered to work with and function correctly in first generation S10 trucks and SUVs.

7/8 Bore Master Cylinder - Smaller bore master cylinders creates higher fluid pressure and reduces effort by the driver. Optional 24mm or 1.0 bore master cylinders for rear disc conversions.

Brake Line Adapters - For ease of installing stock brake lines to the master cylinder supplied in the kit. Detailed (5 Page) Installation Manual. What size master cylinder do you need?

7/8 Bore master cylinder - almost anything with rear drum. 24mm Bore master cylinder - almost anything with a GM or Ford factory rear disc calipers and some aftermarket 1-3/8 diameter 4 piston calipers. 1.0" Bore master cylinder - Any rear disc conversion with a GM metric caliper (no built in parking brake) or aftermarket 4 piston calipers with 1.75" pistons. NOTE: The KIT comes standard with a 7/8" bore master cylinder, but a 24mm or 1.0" bore master cylinder can be substituted at NO CHARGE after you order. 6 to 1 Pedal Ratio - Creates less effort by the driver to stop the car and multiplies the fluid pressure in the system.

No other manual brake conversion kit can match this. Dual Bolt Patter on the Adapter Plate - Use GM, Ford, or MOPAR master cylinders.

No other manual brake conversion kit can do this. Better pedal modulation for consistent braking - No low engine vacuum issues to worry about. The adapter plate is CNC machined by a water jet from rigid 1/8 thick aluminum with dimensions that covers up the hole in the firewall after you remove the power booster.

This modification will clean up your firewall by getting rid of the big, bulky power booster. Racers do this swap when their engine does not make enough vacuum to operate the power booster, to shed a few pound to make their car lighter, or to clean up the engine bay. The pro-touring fans use manual brakes to get a better feel of their brakes when heading into a corner at a high rate of speed.

The adapter plate can also be polished up to a mirror finish if needed. Higher Pedal Ratio = Less Leg Effort = Increased Braking Performance.

Smaller Bore Master Cylinder = Higher Fluid Pressure = Increased Braking Performance. Kit comes with a gasket matched to the adapter plate to seal the passenger compartment from the engine bay. The other kits do not offer a gasket in their kits. Kit comes with a dual bolt pattern to run different master cylinders from GM, Ford, and MOPAR.

The other manual brakes kits do not have this feature. Kit comes with the correct size master cylinder that is matched to the size of the front and rear brakes. The other manual brake kits offer a larger bore master cylinder which generates less brake line pressure. Parts to Enhance Your Manua l Brakes on Y our S10 Truck or SUV. NON Low Drag Caliper (see below) - These type of calipers are manditory to work with the supplied 7/8 bore master cylinder. New Rubber or Stainless Steel Flexible Brakes Lines (front and rear) - Old rubber lines will "balloon" causing loss of pressure within the braking system. LOW drag calipers came on ALL first generation S10 trucks and SUVs. All replacement calipers, with stock piston size, should be rebuilt to NON low drag standards and will work with this KIT. Leg Force Pedal Ratio Master Cylinder Bore Caliper Piston Size Clamping Force. 100 5.5 to 1 1-1/32 (1.03") 2.5" 3240 lb of clamping force with other manual brake systems. There is 34% more clamping force than any other other manual brake systems. I will be happy to answer any of your questions. The item "1982-1994 1st Gen S10 Manual Brake Conversion Kit Disc / Drum 7/8 Bore MC" is in sale since Wednesday, April 18, 2018. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Brakes & Brake Parts\Master Cylinders & Parts".

The seller is "malibudave1978" and is located in Houston, Texas. This item can be shipped to United States.

Manufacturer Part Number: MDS10KITGEN178
Brand: www.manualbrakes.com